
Ceramic
coating
aftercareA GYEON care guide.
How to keep a GYEON coating working for its full life: the first 14 days, washing, what to avoid, and the warranty inspections.
The short
version.
Fully cured at 14 days, then a gentle hand wash every few weeks. How the car is washed matters as much as the coating.
A GYEON coating applied in our studio is water-resistant 12 hours after it goes on and fully cured at 14 days. From then on, how long it lasts depends mostly on how the car is washed and what is left sitting on the paint. This guide is for owners of cars coated at our Caloundra West studio and anyone weighing up a coating; the packages, prices and process are on the GYEON ceramic coating page.
| When | What to do |
|---|---|
| First 12 hours | The car stays in the studio while infrared lamps start the cure. The coating is water-resistant after 12 hours. |
| Days 1 to 14 | Still curing. Water only, no detergents of any kind. Rinse off bird droppings straight away. |
| Every 2 to 4 weeks | A gentle hand wash with a pH-neutral shampoo and clean microfibre. |
| At least every 3 months | A GYEON maintenance product (Q²M Cure, Q²M WetCoat or Q²M Bathe+), as the Infinite warranty requires. |
| Every 6 to 12 months | A coating-safe decontamination, such as an iron fallout remover. |
| Every 24 months or 25,000 km | Infinite only: the periodic inspection that keeps the lifetime warranty active. |
How long does
a coating last?
GYEON Evo Flash carries a 3 to 5 year manufacturer warranty. Infinite lasts around five years self-maintained, and its warranty becomes lifetime when the 24-month inspections are kept.
What shortens it
Harsh chemicals and brush car washes. Strong sun, salt air and bird droppings on a car that lives outdoors. Gravel roads and high kilometres. And poor preparation before it went on, which no amount of care can fix later.
Signs it's wearing
Water stops beading and sits flat on the paint. The car gets harder to dry and to keep clean. Gloss drops, and water spots and stains appear more often and take more work to remove.
What GYEON promises
Under the Infinite terms, a correctly maintained coating keeps its gloss and self-cleaning ability, makes droppings, tar and bugs easier to remove, and keeps beading or sheeting for at least 24 months.
What happens
in the first
14 days?
The coating is still curing, so it gets water only. No detergents for 14 days is a condition of the GYEON warranty, not just advice.
- 01
In the studio
Shortwave infrared starts the cure, and the car stays inside until the first cure is done. You collect it water-resistant.
- 02
Days 1 to 14
If it gets dirty, rinse it with plain water. Rinse bird droppings, sap and bugs off the same day: they are acidic and etch faster in heat. Park out from under trees where you can.
- 03
Day 15 on
The coating is fully cured. Start the normal washing routine below. For Infinite, have any detailing done by a GYEON-approved detailer.
How do I wash
a coated car?
By hand, every 2 to 4 weeks, with a pH-neutral car shampoo, two buckets and clean microfibre, out of direct sun.
Rinse first. Knock loose grit off with a hose or pressure washer before anything touches the paint. Foam helps loosen what is left.
Two buckets. One for shampoo, one for rinsing the mitt. Rinsing in the soapy bucket puts the grit straight back on the paint, and that is where swirl marks come from.
Separate mitts. A mitt that has touched the wheels carries brake dust. Keep different mitts and towels for wheels, paint and glass.
Shade, not sun. Shampoo and water dry too fast on hot panels and leave spots and streaks.
Dry it, don't let it air-dry. A coating sheds most of the water, but tap water left to evaporate still leaves mineral spots. Use clean microfibre towels or a blower.
No dish soap or household cleaners. They attack the coating's chemistry and cut its water repellence. "Wash and wax" shampoos clog it.
Pressure
washer or
car wash?
A pressure washer is fine once the coating has cured, used gently. An automatic car wash is not.
Pressure washing
- Wait until the first 14 days are over.
- Use a 25 or 40 degree fan tip, never a 0 or 15 degree jet.
- Keep the pressure between 1,200 and 1,900 PSI, nearer the lower end.
- Hold the nozzle at least 30 cm from the paint and keep it moving.
- Keep the jet off panel edges, badges and trim, where lifting starts.
Automatic car washes
Brush and tunnel washes drag grit from the cars before yours across the paint and wear the coating down. GYEON's Infinite warranty terms also exclude cars washed in any automatic or commercial car wash, so a touchless wash is out too. If you can't hand wash the car, our detailing team can.
Can I wax over
a coating?
You can, but it works against the coating. Top it up with a GYEON maintenance product instead.
A traditional wax doesn't bond to the coating. It sits on top as a softer layer, hides the slick, water-shedding surface the coating was applied for, and wears off within months. It breaks down unevenly, so the finish ends up patchy or streaky and needs stripping. Cleaner waxes and polishes are worse: they are mildly abrasive and wear the coating itself.
Stacking random spray sealants and "spray waxes" has the same problem. And if the beading has dropped, look at contamination first: built-up road film and fallout reduce gloss and water behaviour until they are removed.
What damages
a coating?
Harsh chemicals, abrasion and contaminants left to bake on. A coating is one to three microns thick and resists a lot, but not those.
Strong chemicals
Strong acids and alkalis, including degreasers and acidic wheel cleaners on painted panels. Ammonia, bleach, vinegar and solvents. Dish soap and household cleaners.
Abrasion
Brush car washes, dirty sponges and old towels, wiping a dry dusty car, and aggressive clay barring. Each one drags grit across the surface and leaves micro-scratches.
Things left on the paint
Bird droppings are acidic and can etch through a coating within hours in the heat. Tree sap, bug splatter, tar, salt and hard water spots do the same more slowly. Remove them as soon as you see them.
Physical damage
Stone chips, keys and impacts go straight through a coating, and it doesn't repair itself. Machine polishing removes it. For stone chips, the answer is paint protection film on the front of the car.
Does paint
colour
matter?
Yes. Black is the hardest colour to keep looking right, and a coating doesn't change that, so dark cars need the gentlest washing of all.
Black and dark colours
Dark paint works like a mirror and shows every swirl mark, water spot, speck of dust and fingerprint. Dark blue and dark grey behave much the same, showing pollen, light dirt and streaks after a wash.
Red
Red is prone to oxidation and fading under strong sun. The UV resistance of a coating helps, as long as the coating itself is kept in good condition.
White and silver
Gloss white shows road dust, mud and tar quickly. Silver and light metallics are the easiest: they hide light scratches and dust well and stay cooler in the sun.
Can a coating
be removed?
Yes, but not by washing. A cured coating is bonded to the clear coat, and the reliable way to take it off is machine polishing.
A dual-action polisher with a cutting compound takes the coating off layer by layer until bare clear coat is showing. It is controllable, and it leaves the paint ready for whatever goes on next. Chemical coating removers and strong alkaline cleaners can soften an old or weak coating, but the result is less predictable and usually still needs a light polish. A clay bar only lifts a coating that is already failing. Wet sanding is reserved for hardened high spots, and it is not a home job: done wrong, it cuts through the clear coat.
Before a new coating goes on, the paint is washed, decontaminated, corrected where it needs it, and wiped with a panel prep so the new layer bonds to clean paint. Swirls or etching under an old coating are dealt with in that machine paint correction step.
The coating has worn out
Water no longer beads, and stains have baked in.
Something else is going on
A new coating, or film, needs bare clear coat underneath.
There are defects under it
Swirls, scratches or etching need correcting first.
A panel is being repaired
Damaged or repaired panels fall outside the Infinite warranty.
How do I keep
the warranty?
We register the coating with GYEON Australia within 30 days of pick-up. After that, keeping it valid comes down to how the car is looked after.
Every coating
No strong detergents for the first 14 days and no automatic brush car washes. Hand wash with a pH-neutral shampoo, and get droppings, sap and bugs off promptly.
Evo Flash
A 3 to 5 year manufacturer warranty, registered under its own certificate number. There is no inspection schedule.
Infinite
Lifetime, as long as the periodic service is done every 24 months or 25,000 km by your GYEON certified detailer; we give you the dates at handover. Miss one and the lifetime cover ends, though the standard five-year warranty can still apply. The terms also rule out any automatic or commercial car wash and detailing by companies GYEON hasn't approved, dealerships included, and need a GYEON maintenance product at least every 3 months.
What it doesn't cover
A coating doesn't stop stone chips or scratches, so the warranty doesn't cover them. The Infinite terms also exclude accident or vandalism damage, track use, commercial vehicles and damaged or repaired panels, and the warranty stays with the registered owner when the car is sold.

Coating or
recoating?
Packages, prices and how the coating goes on are on the ceramic coating page. Questions about a coating you already have, use the form below.
Evo Flash and Infinite are both applied in our Caloundra West studio by a GYEON accredited installer, with decontamination and a single-stage polish in every package. Compare the two systems and the prices by vehicle size on the ceramic coating packages page.